View VS6451R0BATR_4547335.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

VS6451
Ultra small CIF+ reflowable camera module
Data Brief
Features

CIF+ resolution sensor (384x320 or 320x384) Electrical and logical interface fully SMIA compliant Video data interface - CCP2.0 Command interface - CCI 2.8 V/1.8 V operation On-board 10 bit ADC Small physical size Integral EMC shielding Ultra low power standby mode On-chip PLL Lead free reflowable module device can be incorporated in the phone system to run the algorithms in hardware. The STV0984 processor can support 2 cameras. The specifications of these devices are contained in a separate document. The module design is optimized to provide an ultra small footprint and height, and is designed to be reflowable at lead-free solder profiles. The product is lead free. The lens design is optimized for video conferencing and maintains its performance even after the high temperatures of lead-free reflow. VS6451 offers an ultra low power consumption hardware standby mode consuming less than 30 W.
Applications

Mobile phone PDA Videophone
Description
This data brief outlines an ultra small reflowable CIF+ camera module (VS6451) for use across a range of mobile phone handsets and accessories. It is primarily designed to be used as a second camera in video conferencing applications, but could equally be used as a primary camera. The camera silicon device is SMIA class 2 profile 0 compliant and is capable of generating raw bayer CIF+ images up to 30 fps. The VS6451 supports the CCI control and CCP2.0 data interfaces. As different phone platforms have different baseband processors with varying capabilities, it may not be possible for all phones to support the associated image processing algorithms. Where the baseband cannot support this processing load, a separate hardware accelerator (STV0984)
March 2007
Rev 2
1/4
www.st.com
4
For further information contact your local STMicroelectronics sales office.
VS6451
Figure 1.
Application diagram
Figure 2.
Block diagram
VS6451 CIF+ camera module
STV0984 CLK or PDN STV0976 Processor CCI CCP2.0
CLK PDN I2C CCP2.0 or ITU
Baseband or Application Processor
EXTCLK XSHUTDOWN
VS6451
PLL and Clock Management Power Mgmt CCI Receiver Sensor Control Registers Power-On Reset CIF+ Pixel array 1152 x 864 VDIG DGND
Readout
CCI CCP2.0
SMIA Rx'er
CLKP CLKN DATAP DATAN
CCP2.0 Transmitter
VS6451 CIF+ camera module
CLK PDN
Baseband or Application Processor
SCL SDA
SMIA profile 0 frame formatter
Y Decoder
VANA AGND
Column ADC X Decoder Line SRAM
Table 1.
Technical specifications
Parameter Values CIF+ portrait and landscape 0.18 m HCMOS8i shrink 3.6m x 3.6m +8 dB +24 dB (max) 61 dB 34 dB (@ 100 lux) < 7lux Analogue: 2.4V to 2.9V Digital: 1.8V 0.1V <60 mW 4.5 mm x 4.5 mm x 3.55 mm 45+/- 2 (CIF+, CIF equiv. 45) 2.8 On axis 45% (typ) Horizontal field (70%) 25% (typical) <|5%| 60% (typ) Lead free reflowable BGA [-40; +85]C [-30; +70]C [-25; +55]C [+5; +30]C
Pixel array Sensor technology Pixel size Exposure control Analogue gain Dynamic range Signal to noise Minimum illumination Supply voltage Average power consumption @ 30fps Module size (XYZ) max Lens HFOV F number Lens SFR Lens TV distortion Relative illumination System connectivity Storage temperature Functional operating temperature Normal operating temperature Optimal operating temperature
2/4
VS6451 Figure 3. Module outline
4.50
Ordering information
3.55 4.50
Ordering information
Table 2. Order codes
Part number VS6451R0BA/TR Package USM- CIF - 4.5x4.5x3.55mm Packing Tape and reel
Revision history
Table 3.
Date 27-Apr-2006 13-Mar-2007
Document revision history
Revision 1 2 Initial release. Updated the ordering information and module outline Changes
3/4
VS6451
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
4/4

▲Up To Search▲

Price & Availability of VS6451R0BATR

	To Download VS6451R0BATR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .